Advertisement [ ? ]
Site Links
- Lease Calculator
- Advertise
- My Car ongoing Review
- Members' Chat
- Cars For Sale
- Car Dealers
- Honda "Fit" Manual
- Hyperflex Bushings
- For Sale
- Fix your Car
- Car Manuals
- other manuals - Reference Materials
- DIY Repairs
- Articles
- Video
- Link with Us
- Search Help
- Code your Mac!
- Fly, race, anything R/C
Honda Fit/Jazz - Manual Transmission Reassembly (5MT)
Online Honda Fit/Jazz 2002-2005 Workshop repair manual used by professionals.
Full Membership required
We can not locate your Full (Preferred) membership details. Please login to your account first and if necessary upgrade your membership.
24 Hr or Annual Membership required.
Thank you!
Snip from the Manual
Manual Transmission Reassembly
NOTE: Prior to reassembling, clean all the parts in solvent, dry them, and apply lubricant to any contact surfaces.1.Install the magnet (A) and differential assembly (B).
IMAGE REPLACED HERE
2.Install the 8 mm spring washer (A) and the 8 mm special bolt (B).
3.Install the 36 mm spring washer (C) and 26 mm washer (D) over the ball bearing (E). Note the installation direction of the spring washer (C).
IMAGE REPLACED HERE
4.Tape the mainshaft splines (F) with vinyl tape to protect the seal. Install the mainshaft and countershaft (G) into the shift forks (H), and install them as an assembly.
5.Install the reverse lock cam.
IMAGE REPLACED HERE
6.Install the reverse shift fork.
IMAGE REPLACED HERE
7.Install the reverse idler gear (A) and reverse gear shaft (B).
IMAGE REPLACED HERE
8.Select the proper size 72 mm shim (A) according to the measurements made during the Mainshaft Thrust Clearance Adjustment (see page 13-52). Install the oil gutter plate (B), oil guide plate M, and 72 mm shim into the transmission housing (C).
NOTE: Align the groove (D) of the transmission housing to the mark and finger (E) of oil guide plate M, and install it.
IMAGE REPLACED HERE
9.Remove the dirt and oil from the transmission housing sealing surface. Apply liquid gasket (P/N 08C70-K0234M) to the sealing surface. Be sure to seal the entire circumference of the bolt holes to prevent oil leakage.
NOTE: If 5 minutes have passed after applying liquid gasket, reapply it and assemble the housings. Allow it to cure at least 20 minutes after assembly before filling the transmission with oil.
IMAGE REPLACED HERE
10.Install the 14 x 20 mm dowel pins (A).
IMAGE REPLACED HERE
11.Make the finger (B) of tapered cone ring touch the 5th shift fork (C) as shown.
12.Lower the transmission housing the rest of the way as you expand the 52 mm snap ring (D). Release the snap ring so it seats in the groove of the countershaft bearing.
13.Check that the 52 mm snap ring is securely seated in the groove of the countershaft bearing.
(0.18 - 0.33 in.)
14.Apply liquid gasket (P/N 08C70-K0234M) to the threads of the 32 mm sealing screw (E), and install it on the transmission housing.
15.Install the transmission hanger (A) and the 8 mm flange bolts finger-tight.
IMAGE REPLACED HERE
16.Tighten the 8 mm flange bolts in a crisscross pattern in several steps.
IMAGE REPLACED HERE
17.Remove the dirt and oil from the shift lever cover sealing surface. Apply liquid gasket (P/N 08C70-K0234M) to the sealing surface.
IMAGE REPLACED HERE
18.Install the 8 x 10 mm dowel pins (A) and shift lever assembly (B).
IMAGE REPLACED HERE
19.Install the set screws (A), new 12 mm washers, springs, and steel balls.
IMAGE REPLACED HERE
20.Install the new washer and back-up light switch.
21.Install the new washer (A), drain plug (B), filler plug (C), new O-ring (D), and vehicle speed sensor (VSS) (E).
IMAGE REPLACED HERE
assembly. 5.