Advertisement [ ? ]
Site Links
- Lease Calculator
- Advertise
- My Car ongoing Review
- Members' Chat
- Cars For Sale
- Car Dealers
- Honda "Fit" Manual
- Hyperflex Bushings
- For Sale
- Fix your Car
- Car Manuals
- other manuals - Reference Materials
- DIY Repairs
- Articles
- Video
- Link with Us
- Search Help
- Code your Mac!
- Fly, race, anything R/C
Honda Fit/Jazz - How to Troubleshoot CVT Systems (CVT)
Online Honda Fit/Jazz 2002-2005 Workshop repair manual used by professionals.
Full Membership required
We can not locate your Full (Preferred) membership details. Please login to your account first and if necessary upgrade your membership.
24 Hr or Annual Membership required.
Thank you!
Snip from the Manual
How to Troubleshoot CVT Systems
How to Check for DTCs with the PGM Tester/Scan Tool
When the PCM senses an abnormality in the input or output systems, the D indicator (A) in the gauge assembly (B) will usually blink and/or the Malfunction Indicator Lamp (MIL) will come on.
IMAGE REPLACED HERE
When the 16P Data Link Connector (DLC) (A) (located under the dash on driver's side) is connected to the OBD Scan Tool or Honda PGM Tester (B) as shown, it will indicate the Diagnostic Trouble Code (DTC).
IMAGE REPLACED HERE
If the D indicator or MIL has been reported on, or if a driveability problem is suspected, follow this procedure:1.Connect the OBD Scan Tool or Honda PGM Tester to the DLC. (See the OBD Scan Tool or Honda PGM Tester user's manual for specific instructions. If you are using the Honda PGM Tester, make sure it is set to the SAE DTC type).
2.Turn the ignition switch ON (II), and observe the DTC on the screen.
3.Record all fuel and emissions DTCs, A/T DTCs, and freeze data.
4.If there is a fuel and emissions DTC, first check the fuel and emissions system as indicated by the DTC except for DTC P0700. DTC P0700 means there is one or more A/T DTC, and no problems were detected in the fuel and emissions circuit of the PCM.
5.Reset the DTC stored in the PCM with the OBD Scan Tool or PGM Tester.
Calibrate the feedback signal for the start clutch control.
7.Drive the vehicle for several minutes in the freeze data conditions, or at speeds over 50 km/h (30 mph), and then recheck for DTC(s). If the A/T DTC returns, go to the DTC Troubleshooting Index. If the DTC does not return, there was an intermittent problem within the circuit. Make sure all pins and terminals in the circuit are tight.
8.Reset the radio preset stations, and set the clock.
How to Troubleshoot Circuits at the PCM
1.Remove the glove box cover and glove box.
2.Remove the passenger's lower cover, then remove the access cover.
3.Inspect the circuit on the PCM, according to the DTC troubleshooting, with a digital multitester (A) and tapered tip probe (B) as shown.
IMAGE REPLACED HERE
4.If you cannot get to the wire side of the connector or the wire side is sealed, disconnect the connector and use the tester probe to probe the connectors from the terminal side. Do not force the probe into the connector.
PCM Reset Procedure
1.Write down the radio station presets.
2.Turn the ignition switch OFF.
3.Remove the No. 20 ECU fuse (15A) (A) from the under-hood fuse/relay box (B) for more than 10 seconds.
IMAGE REPLACED HERE
How to End a Troubleshooting Session
This procedure must be done after any troubleshooting.
1.Turn the ignition switch OFF.
2.Disconnect the Honda PGM tester (A) from the DLC (B).
IMAGE REPLACED HERE
3.Reset the PCM.
Calibrate the feedback signal for the start clutch control.
5.Turn the ignition switch ON (II).
6.To verify that the problem is repaired, test-drive the vehicle for several minutes at speed over 50 km/h (30 mph).