Advertisement [ ? ]
Site Links
- Lease Calculator
- Advertise
- My Car ongoing Review
- Members' Chat
- Cars For Sale
- Car Dealers
- Honda "Fit" Manual
- Hyperflex Bushings
- For Sale
- Fix your Car
- Car Manuals
- other manuals - Reference Materials
- DIY Repairs
- Articles
- Video
- Link with Us
- Search Help
- Code your Mac!
- Fly, race, anything R/C
Honda Fit/Jazz - DTC Troubleshooting: P0141 (65-2) (5MT)
Online Honda Fit/Jazz 2002-2005 Workshop repair manual used by professionals.
Full Membership required
We can not locate your Full (Preferred) membership details. Please login to your account first and if necessary upgrade your membership.
24 Hr or Annual Membership required.
Thank you!
Snip from the Manual
DTC Troubleshooting: P0141 (65-2)
DTC P0141 (65-2): Secondary HO2S (Sensor 2) Heater Circuit Malfunction
1.Reset the ECM/PCM.
2.Start the engine.
Is DTC P0141 indicated?
YES - Go to 3.
NO - Intermittent failure, system is OK at this time. Check for poor connections or loose wires at the secondary HO2S (Sensor 2) and at the ECM/PCM.n
3.Turn the ignition switch OFF.
4.Disconnect the secondary HO2S (Sensor 2) 4P connector.
5.At the secondary HO2S (Sensor 2) side, measure resistance between the HO2S 4P connector terminals No. 3 and No. 4.
IMAGE REPLACED HERE
Is there about 11 W (at room temperture)?
YES - Go to 6.
NO - Replace the secondary HO2S (Sensor 2).n
6.Check continuity between body ground and the secondary HO2S (Sensor 2) 4P connector terminals No. 3 and No. 4 individually.
IMAGE REPLACED HERE
Is there continuity?
YES - Replace the secondary HO2S (Sensor 2).n
NO - Go to 7.
7.Turn the ignition switch ON (II).
8.Measure voltage between the secondary HO2S 4P connector terminals No. 3 and No. 4.
IMAGE REPLACED HERE
Is there battery voltage?
YES - Go to 9.
NO - Go to 13.
9.Turn the ignition switch OFF.
10.Disconnect the negative cable from the battery.
11.Disconnect ECM/PCM connector E (31P).
12.Check for continuity between ECM/PCM connector terminal E6 and body ground.
IMAGE REPLACED HERE
Is there continuity?
YES - Repair short in the wire between the ECM/PCM (E6) and the secondary HO2S (Sensor 2).n
NO - Substitute a known-good ECM/PCM and recheck . If symptom/indication goes away, replace the original ECM/PCM.n
13.Measure voltage between the secondary HO2S (Sensor 2) 4P connector terminal No. 4 and body ground.
IMAGE REPLACED HERE
Is there battery voltage?
YES - Go to 14.
NO - Check the No. 16 ACG (7.5A) fuse in the under-dash fuse/relay box. If the fuse is OK, repair open in the wire between the secondary HO2S (Sensor 2) and No. 16 ACG (7.5A) fuse.n
14.Turn the ignition switch OFF.
15.Disconnect the negative cable from the battery.
16.Reconnect the secondary HO2S (Sensor 2) 4P connector.
17.Disconnect ECM/PCM connector E (31P).
18.Reconnect the negative cable to the battery.
19.Turn the ignition switch ON (II).
20.Measure voltage between ECM/PCM connector terminal E6 and A5.
IMAGE REPLACED HERE
Is there 0.1 V or less?
YES - Repair open in the wire between the ECM/PCM (E6) and the secondary HO2S (Sensor 2).n
NO - Substitute a known-good ECM/PCM and recheck . If symptom/indication goes away, replace the original ECM/PCM.n
YES -