DIY     OBD-II Codes     Fix your Car     Repair Manuals     -Forum-

Advertisement  [ ? ]

Site Links

Digg Twitter FaceBook

Honda Fit/Jazz - DTC Troubleshooting: P0135 (41-2) (5MT without ETCS)

Online Honda Fit/Jazz 2002-2005 Workshop repair manual used by professionals.

Full Membership required

We can not locate your Full (Preferred) membership details. Please login to your account first and if necessary upgrade your membership.
24 Hr or Annual Membership required.

Thank you!

Snip from the Manual


DTC Troubleshooting: P0135 (41-2)

DTC P0135 (41-2): Primary HO2S (Sensor 1) Heater Circuit Malfunction


1.Reset the ECM/PCM.

2.Start the engine.

Is DTC P0135 indicated?


YES - Go to 3.


NO - Intermittent failure, system is OK at this time. Check for poor connections or loose terminals at the primary HO2S (Sensor 1) and at the ECM/ PCM.n


3.Turn the ignition switch OFF.

4.Disconnect the primary HO2S (Sensor 1) 4P connector.

5.At the primary HO2S side, measure resistance between the primary HO2S (sensor 1) 4P connector terminals No. 3 and No. 4.

IMAGE REPLACED HERE

Is there about 6 W (at room temperature)?


YES - Go to 6.


NO - Replace the primary HO2S (Sensor 1).n

6.Check for continuity between body ground and the primary HO2S (Sensor 1) 4P connector terminals No. 3 and No. 4 individually.

IMAGE REPLACED HERE

Is there continuity?


YES - Replace the primary HO2S (Sensor 1).n


NO - Go to 7.


7.Turn the ignition switch ON (II).

8.Measure voltage between the primary HO2S (Sensor 1) 4P connector terminal No. 3 and No. 4.

IMAGE REPLACED HERE

Is there battery voltage?


YES - Go to 9.


NO - Go to 12.


9.Turn the ignition switch OFF.

10.Disconnect ECM/PCM connector A (31P).

11.Check for continuity between ECM/PCM connector terminal A1 and body ground.

IMAGE REPLACED HERE

Is there continuity?


YES - Repair short in the wire between the ECM/PCM (A1) and the primary HO2S (Sensor 1).n


NO - Update the ECM/PCM if it does not have the latest software, or substitute a known-good ECM/PCM, then recheck. If the symptom/indication goes away with a known-good ECM/PCM, replace the original ECM/PCM.n


12.Measure voltage between the primary HO2S (Sensor 1) 4P connector terminal No. 3 and body ground.

IMAGE REPLACED HERE

Is there battery voltage?


YES - Go to 13.


NO - Check the No. 3 (7.5A) fuse in the under-dash fuse/relay box. If the fuse is OK, repair open in the wire between the primary HO2S (Sensor 1) and No. 3 (7.5A) fuse.n

13.Turn the ignition switch OFF.

14.Reconnect the primary HO2S (Sensor 1) 4P connector.

15.Disconnect ECM/PCM connector A (31P).

16.Turn the ignition switch ON (II).

17.Measure voltage between ECM/PCM connector terminal A1 and A5.

IMAGE REPLACED HERE

Is there 0.1 V or less?


YES - Repair open in the wire between the ECM/PCM (A1) and the primary HO2S (Sensor 1).n


NO - Update the ECM/PCM if it does not have the latest software, or substitute a known-good ECM/PCM, then recheck. If the symptom/indication goes away with a known-good ECM/PCM, replace the original ECM/PCM.n

(at


Honda Fit/Jazz 02-05 Workshop Manual    Back to all Manuals